After several nights of templating, marking, trimming, cutting and then shaping and glueing the floor and side tank bearers I finally fitted the fwd bulkheads tonight. There is no plan for these bulkheads in the plans, so they took quite a bit of cardboard templating, and marking out of the curved floor bearers and position of side tank bearer and carlin notches etc
2 Comments
Picked up the Farr from Daryl for a trial spell at Draycote.
First impressions : Boat looks great, lots of admiring comments, it helps that Sacre Bleu is well tricked out. Rigging is very simple, but I don't get this no halyard deal, especially when coming back ashore between races, and having to roll the boat over. I found hoisting had to be a two man job, one feeding, one hoisting. Mine will have a halyard! Sailing : Sunday started F2-3 and built during the day to some solid F5 gusts which proved to be perfect demo conditions. My first impression sailing away from the beach was, goodness, this boat is tiny ! Not space wise, it has a lovely wide open cockpit, but it is a short boat and quite sensitive to positioning. This was my first time trapezing in probably 20 yrs and my firt trapeze helming which was interesting. The Farr is very stable and can be easily balanced with increasing sheet loads as you step out on the wire, it is then very comfortable and responsive. It didn't feel like it pointed very high, but as the wind built you can load up the kicker and feel the extra power building thru the fully battened main, comparing against other boats then showed the pointing to be comparable. Coming from a fine entry RS 300, the fuller bows make a lot of noise, and on a fast tight reach, the spray makes it quite a wet ride. On a fast deep reach as the wind built I thought I try a gybe, it was a breeze, and the light weight means it is so easy to make body weight corrections to recover any errors. For my this was a joy, sailing a boat in strong wind, that I did';t feel overpowered in. I had a couple of screaming deep reaches in some strong gusts that had the whole boat humming and me shouting 'Whooppeee' until I let it come over on me a fraction too much and ended up getting T bagged, with the rig swinging back up and me being dragged alongside the boat. I found it quite hard to right, mast filled with water, slippy hull and raked daggerboard all conspired, I might have to resort to righting lines on mine if I keep venturing out in the windy stuff !. Once it rolled right over on top of me as I righted, but it was possible to stop this by being a lot more agile getting across. The biggest issue I had was with the 1.8m tiller extension. This is too long to go past the shrouds and lowers, so if I held it across in front of me, then came in off the wire, it go trapped between me and the shroud .. swim!. I also found that with full kicker on in the stronger stuff it was very easy to get into irons if a bot slow when tacking, then difficult to get going again. (goes well backwards!). More practice needed. I raced a Supernova and L2000, we were all similar speed upwind, although I think with better helming the Farr would be quicker, it was slower deep downwind, but left them for dead on a powered up tight reach. A great days sailing (good job really as I'm pretty co Tonight I built and fitted the angled front deck beams. This was pretty tricky as they sit in fresh air, needed to be deeper than any cedar strip I had left, and are curved to match the upper shape of frames one and two.
I carefully notched and angled the ends to fit against the inner gunwhale and frame 2 and cut two lengths to laminate one above the other. I then used a pencil taped to the end of a long strip to trace the curve of frames one and two before fretsawing the beams to match. Then laminated, glued and clamped them in place ... phew Cut the stem, unscrewed the hull from the temporary frames and with a little help lifted her out of the shed. Great to see her the right way up, felt really light ( I must find some scales). The internal structure looks good, but there are a few thin glue lines and gaps under some of the stringers so a bunch of filleting is required. This is a real milestone, but also highlights how much work is left to do ... better crack on ! Mixed some filleting blend, poured it into a ziplog bag, cut the corner off and cake iced it along each stringer. Not as easy as I thought, I'm glad these joints won't be on show !
|
Archives
November 2016
Categories
All
|